34CrMo4 datasheet, 34CrMo4 mechanical properties, chemical element 34CrMo4, technical specifications of 34CrMo4 steel material properties. 34CrMo4 performance specifications. 34CrMo4 datasheet,34CrMo4 chemical,34CrMo4 heat Specification 34CrMo4 datasheet, Inventory 34CrMo4 Chemical, Stocklist 34CrMo4 forging, Bar, Sheet -steelmaking, ESR, blooming, hot forging, hot rolling, heat treatment, straightened, ultrasonic test,cold working,machined. We also possess advanced precision machining equipments for further processing.
EN 10297-1 Grade 34CrMo4 Specification.EN 10297-1 Grade 34CrMo4 Carbon Steel Seamless Tubes are most commonly used for general purpose applications worldwide.EN 10297-1 Grade 34CrMo4 Tubes are ductile and strong Tubes with long wearing properties .These Tubes are manufactured as per EN Specification and commercially referred as carbon steel Tubes. Datasheet for Steel Grades Carbon Steel 34CrMo4This page is mainly introduced the 34CrMo4 Datasheet,including 34CrNiMo6 1.6582 4337 Engineering Steel - Otai Special EN 34CrNiMo6 Steel is an important alloy engineering steel grade as per BS EN 10083-3:2006. Otai Steel is reliablel EN 34CrNiMo6 engineering steel supplier. 35CrMo Steel Chemical Composition, Mechanical Properties 35CrMo Steel. 35CrMo steel is a Chinese alloy steel for engineering purpose, it has high durability and creep strength at high temperature, and low temperature impact toughness is good. The working temperature is up to 500 °C, the low temperature can be -100 °C, and has high static strength and high fatigue strength, good hardenability, no tendency to overheat, small quenching deformation
42CrMo4, 1.7225, 42CrMoS4, 1.7227, AISI 4140 description. Structural steel, strong and hardenable. With this steel one can achieve very good properties on the whole cross-section (while quenching in oil, the max diameter is 70mm, for quenching in water it is 50mm). In the surface hardened condition in achieves a hardness of 54-59 HRC on the EN 1.7220 (34CrMo4) Chromium-Molybdenum Steel May 30, 2020 · EN 1.7220 (34CrMo4) Chromium-Molybdenum Steel EN 1.7220 steel is an alloy steel formulated for primary forming into wrought products. 1.7220 is the EN numeric designation for this material. 34CrMo4 is the EN chemical designation. EN 10250 Open steel die forgings for general engineering Steel and Cast Iron Standards. EN 10250:Steel grades /numbers. EN 10250-1:1999 Open steel die forgings for general engineering purposes. General requirements. EN 10250-2:2000 Open steel die forgings for general engineering purposes. Non-alloy quality and special steels. COMPARE GRADES. 1.0038 S235JRG2.
din en 10263-4 1.7225 42crmo4 / din en 10269 1.7225 42crmo4 / astm a331, a505, a519, a646 aisi 4137, 4140 b.s. 708a42, 708h37, 708m40, 709m40, en19, en19a, en19b, en19c jis scm4, scm4h, scm440, scm440h afnor 40cd4, 42cd4 / 40cd4u, 42cd4u vergÜtungsstahl chemische zusammensetzung (in massen-% nach din en 10083-3) c si mn p s cr mo Low alloy high strength 34CrMoS4 alloy steel plate to EN Near the blue brittleness temperature, the 34CrMoS4 alloy steel plate to EN 10083-3 strength increases and the plasticity decreases. The elongation and section shrinkage of 34CrMoS4 alloy steel plate to EN 10083-3 increase with the increase of temperature, but there is Ovako 34CrMo4 EN10083-3:2006 Steel - MatWebSteel, General Information:SAE4130m is a low alloyed steel used in quenched and tempered condition. The nearest equivalents are 34CrMo4 in EN10083-3 or 4130 in ASTM A29 with some deviations. The material is delivered as rolled or annealed.
Alloy steel, quenched and tempered 7) 0,20 0,55 0,035 0,035 12.9 5), 6) Alloy steel, quenched and tempered 7) 0,20 0,50 0,035 0,035 380 M18 34CrMo4, 37Cr4, 41Cr4 M24 42CrMo4 M39 34CrNiMo6 1) Free cutting steel is allowed for these property classes with the following maximum sulphur, phosphorus and lead contents:sulphur:0,34%; Steel Chart - Stellenbosch UniversityHigh-alloy steel Steel castings 03.11 1501-509;510 - - ASTM A353 1.5662 X8Ni9 - X10Ni9 XBNi09 - 03.11 - - - 2515 1.5680 12Ni19 Z18N5 - - - 03.11 832M13 36C - - 1.6657 14NiCrMo134 - 15NiCrMo13 14NiCrMo131 - 03.11 BD3 - - D3 1.2080 X210Cr12 Z200C12 X210Cr13KU X210Cr12 SKD1 X250Cr12KU 03.11 2314 1..2083 TECHNICAL DATA COMPARISON OF MATERIALS 18CrMo4 18CrMoS4 34CrMo4 34CrMoS4 34CrMo4 34CrMoS4 42CrMo4 42CrMoS4 Structual manga- nese steel for machine Structual use and manganese chrome steel Aluminum chrome molybdenum ) 1 BS EN 10259 2 DIN 1654 Part 4 3 DIN 17240 4 NF EN 10259 5) Steel C Structure C 400N/mm 2 Steel C 0.45%C C Cr C Mo 435 C Ni C Cr C Mo 220 C Kogu(Tool)C 105 types C
We have online service for you at any time, welcome to contact and learn more information about pressure vessel steel, such as EN 10083-3 34CrNiMo6 sheet ASTM A537 class 1 equivalent, 16Mo3 datasheet, Q245R material properties, Q345R material specification, P355GH properties, pressure vessel steel 34CrMo4 - OvakoMaterial data sheet Steel grade Last revised:Thu, 01 Oct 2020 12:56:40 GMT 34CrMo4 All General Information SAE4130m is a low alloyed steel used in quenched and tempered condition. The nearest equivalents are 34CrMo4 in EN10083-3 or 4130 in ASTM A29 with some deviations. The material is delivered as rolled or annealed. Chemical composition